欧美a级黄片,中文字幕精品久久久久人妻红杏1,福利久久,亚洲AV无码片一区二区三区_

(2)改變轉速的方法：改變皮帶輪外徑或改變齒輪減速器傳動比，也可選用不同轉速的動力機。

(3)水泵轉速改變后，其流量(Q)、揚程(H)和功率(N)的變化關系如下式所示： Q1=Q*n1/n   H1=H*(n1/n)2    N1=N*(n1/n)3

 式中：Q1、H1、N．分別代表轉速改變后的流量、揚程和功率。 Q、H、N分別代表規定轉速下的流量、揚程和功率。

(4)水泵轉速提高后，耗用功率增加，吸上真空度降低，壽命縮短。過分提高轉速會發生其它事故，故應慎用。

(5)水泵轉速過分降低時，泵的使用效益低，為此，應盡量避免泵在過低轉速下運行。用戶應按性能曲線圖選擇使用。

臥式軸流泵@達坂城臥式軸流泵@250HW-4臥式軸流泵生產廠家

軸承發熱，軸封發熱，轉子竄動大，發生水擊一，泵不能發動或發動負荷大要素及處理辦法如下。原動機或電源不正常。處理辦法：查看電源和原動機狀況。泵卡住。處理辦法：用手盤動聯軸器查看，必要時崩潰查看，消除動靜有些毛病。填料壓得太緊。處理辦法：放松填料。排出閥未關。處理辦法：封閉排出閥，從頭發動。平衡管不曉暢。處理辦法：疏通平衡管。

2、允許吸上真空度[Hs]與必需汽蝕余量[NPSH]r的換算關系：

 [Hs]≈10-[HPSH]c

 [NPSH]r≈[NPSH]C+0.3

 式中：[Hs]-允許吸上真空度   米

 [NPSH]C-臨界汽蝕余量   米

 [NPSH]r-必需汽蝕余量   米

臥式軸流泵@達坂城臥式軸流泵@250HW-4臥式軸流泵生產廠家

 *特征描述

HW 型蝸殼式混流泵是按國家標準系列而設計的高節能產品。其性能指標均達到先進水平，省材節能效果顯著。延伸搜索：水環真空泵

（一）用途
HW型混流泵為臥式、單級、單吸、懸臂蝸殼式混流泵，適用于農田排灌、工業、城鎮給排水及船塢、碼頭引水等。延伸搜索：水環真空泵
（二）特點
體積小、重量輕、流量大、效率高，汽蝕性能好，區范圍寬廣而平坦，結構簡單，使用管理方法，維修容易。延伸搜索：水環真空泵
（三）型號說明
以250HW—8為例：
250—泵進（出）水口直徑為250毫米。
8—泵總揚長為8米。

（四）水泵的傳動方式
我廠生產的HW型系列混流泵均機（電）兩用，其轉動方式視各地區動力情況而定，訂貨時根據原動機的型號（功率、轉速）確定水泵的傳動方式，以定皮帶輪的大小或聯軸器的規格。延伸搜索：水環真空泵
（五）水泵轉向：
從水泵進水口看葉輪為逆時針方向旋轉（即箭頭所示的方向旋轉）。

臥式軸流泵@達坂城臥式軸流泵@250HW-4臥式軸流泵生產廠家

當混流泵葉輪在水中旋轉時，葉片對誰既產生離心力作用，又具有升力作用，葉輪轉動時靠這兩種里的混合作用，所以稱為混流泵。當原動機帶動葉輪旋轉后，對液體的作用既有離心力又有軸向推力，是離心泵和軸流泵的綜合，液體斜向流出葉輪。因此它是介于離心泵和軸流泵之間的一種泵。混流泵的比轉速高于離心泵，低于軸流泵，一般在300-500之間。它的揚程比軸流泵高。

Instructions for use (i) the HW mixed-flow pump is composed of main parts such as pump body, pump cover, impeller, pump shaft and bearing body. (Ii) The pump cover is a part of the pump connected to the inlet pipe, with a specified axial end gap between the end surface and the impeller (maintaining the specified axial bance after eliminating the axial activity gap of the bearing). The gap is too small to produce friction, too large will lead to the pump pressure water reflux, so that the pump efficiency is reduced, through the increase or decrease adjustment paper pad to meet the required requirements of the gap. Extended search: Water ring Vacuum Pump (iii) The sealing device is composed of a filler letter, a water seal letter, a filler cover and a lead powder (or oil immersion) asbestos root. Its role is: 1, in the tea to prevent air inhalation pump, play a sealing role. 2. When pumping, prevent water from flowing out of the pump too much along the shaft. (Iv) Shaft application to protect the shaft does not make it directly friction with the filler, if long-term use found that the bushing wear too much, can change the bushing. (V) The two supports of the pump shaft are bearings in the bearing body, and the bearing has an appropriate amount of grease in its body to lubricate the bearings. (Vi) The baffle on the shaft prevents water from flowing into the bearing body along the pump, thus protecting the bearing and extending its service life.