欧美a级黄片,中文字幕精品久久久久人妻红杏1,福利久久,亚洲AV无码片一区二区三区_

(2)改變轉速的方法：改變皮帶輪外徑或改變齒輪減速器傳動比，也可選用不同轉速的動力機。

(3)水泵轉速改變后，其流量(Q)、揚程(H)和功率(N)的變化關系如下式所示： Q1=Q*n1/n   H1=H*(n1/n)2    N1=N*(n1/n)3

 式中：Q1、H1、N．分別代表轉速改變后的流量、揚程和功率。 Q、H、N分別代表規定轉速下的流量、揚程和功率。

(4)水泵轉速提高后，耗用功率增加，吸上真空度降低，壽命縮短。過分提高轉速會發生其它事故，故應慎用。

(5)水泵轉速過分降低時，泵的使用效益低，為此，應盡量避免泵在過低轉速下運行。用戶應按性能曲線圖選擇使用。

灌溉混流泵@若羌灌溉混流泵@350HW-8灌溉混流泵廠家直營

潛水軸流泵研究計劃與數值模子，CFD闡發利用在潛水混流泵水力計劃中能夠低落計劃周期本錢，可經由過程摹擬流態和數據闡發挑選良好的水力模子。)潛水混流泵葉片數越多，到達計劃點流量、揚程越高，葉輪出口速率增大，水力喪失增大，服從降低。依照2種葉輪和4種導葉計劃計劃進行組合獲得8種水力計劃計劃。

2、允許吸上真空度[Hs]與必需汽蝕余量[NPSH]r的換算關系：

 [Hs]≈10-[HPSH]c

 [NPSH]r≈[NPSH]C+0.3

 式中：[Hs]-允許吸上真空度   米

 [NPSH]C-臨界汽蝕余量   米

 [NPSH]r-必需汽蝕余量   米

灌溉混流泵@若羌灌溉混流泵@350HW-8灌溉混流泵廠家直營

 *特征描述

HW 型蝸殼式混流泵是按國家標準系列而設計的高節能產品。其性能指標均達到先進水平，省材節能效果顯著。延伸搜索：水環真空泵

（一）用途
HW型混流泵為臥式、單級、單吸、懸臂蝸殼式混流泵，適用于農田排灌、工業、城鎮給排水及船塢、碼頭引水等。延伸搜索：水環真空泵
（二）特點
體積小、重量輕、流量大、效率高，汽蝕性能好，區范圍寬廣而平坦，結構簡單，使用管理方法，維修容易。延伸搜索：水環真空泵
（三）型號說明
以250HW—8為例：
250—泵進（出）水口直徑為250毫米。
8—泵總揚長為8米。

（四）水泵的傳動方式
我廠生產的HW型系列混流泵均機（電）兩用，其轉動方式視各地區動力情況而定，訂貨時根據原動機的型號（功率、轉速）確定水泵的傳動方式，以定皮帶輪的大小或聯軸器的規格。延伸搜索：水環真空泵
（五）水泵轉向：
從水泵進水口看葉輪為逆時針方向旋轉（即箭頭所示的方向旋轉）。

灌溉混流泵@若羌灌溉混流泵@350HW-8灌溉混流泵廠家直營

密封，支座或根底共振，管路，機器共振，齒輪嚙合不良或磨損。處理辦法：同4，加固根底或管路。振蕩頻率非常高。密封，軸承，齒輪不精細，軸承顫動，不良的收縮合作等。處理辦法：同4。軸承發熱要素及處理辦法如下：1，軸承瓦塊刮研不合請求。處理辦法：從頭修補軸承瓦塊或替換。軸承空隙過小。處理辦法：從頭調整軸承空隙或刮研。光滑油量缺乏，油質不良。處理辦法：添加油量或替換光滑油。軸承安裝不良。處理辦法：按請求查看軸承安裝狀況，消除不合請求要素。冷卻水?dāng)嗦贰Ｌ幚磙k法：查看，修補。軸承磨損或松動。處理辦法：修補軸承或作廢。若松動，復緊有關螺栓。泵軸曲折。處理辦法：糾正泵軸。甩油環變形。甩油環不能滾動，帶不上油。處理辦法：更新甩油環。

Instructions for use (i) the HW mixed-flow pump is composed of main parts such as pump body, pump cover, impeller, pump shaft and bearing body. (Ii) The pump cover is a part of the pump connected to the inlet pipe, with a specified axial end gap between the end surface and the impeller (maintaining the specified axial bance after eliminating the axial activity gap of the bearing). The gap is too small to produce friction, too large will lead to the pump pressure water reflux, so that the pump efficiency is reduced, through the increase or decrease adjustment paper pad to meet the required requirements of the gap. Extended search: Water ring Vacuum Pump (iii) The sealing device is composed of a filler letter, a water seal letter, a filler cover and a lead powder (or oil immersion) asbestos root. Its role is: 1, in the tea to prevent air inhalation pump, play a sealing role. 2. When pumping, prevent water from flowing out of the pump too much along the shaft. (Iv) Shaft application to protect the shaft does not make it directly friction with the filler, if long-term use found that the bushing wear too much, can change the bushing. (V) The two supports of the pump shaft are bearings in the bearing body, and the bearing has an appropriate amount of grease in its body to lubricate the bearings. (Vi) The baffle on the shaft prevents water from flowing into the bearing body along the pump, thus protecting the bearing and extending its service life.