背貼式橡膠止水帶320*6mm
橡膠止水帶混凝土中有許多尖角的石子和銳利的鋼筋頭，由于塑料和橡膠的撕裂強度比拉伸強低3-5倍，止水帶一旦被刺破或撕裂時，不需很大外外力裂口就會擴大，所以在止水帶定位和混凝土澆搗過程中，應注意定位方法和澆搗壓力，以免止水帶被刺破，影響止水效果,具體注意事項如下:
The rubber sealing belt has many sharp stones and sharp head reinforced concrete, the tear strength of rubber and plastic tensile and low 3-5 times, once the waterstop punctured or torn, without external force gap will expand, so the waterstop bing and concrete pouring process, should pay attention to bing b and pouring pressure, so as to avoid the water stop is punctured, influence the sealing effect, the specific considerations are as follows:
1 止水帶不得長時間露天曝曬，防止雨淋，勿與污染性強的化學物質接觸。
The 1 water stop belt should not be exposed to the open air for a long time, prevent the rain, and do not contact with the chemicals with strong pollution.
2 在運輸和施工中，防止機械，鋼筋損傷止水帶。
背貼式橡膠止水帶320*6mm
2 in transport and construction, prevent machinery, steel damage stop water zone.
3 施工過程中，止水帶必須可靠固定，避免在澆注混凝土時發生位移，保證止水帶在混凝土中的正確位置。
3 during the construction process, the water stop belt must be fixed reliably, avoiding the displacement of the concrete in the concrete and ensuring the correct b of the water stop zone in the concrete.
4 固定止水帶的方法有：利用附加鋼筋固定；專用卡具固定；鉛絲和模板固定等，如需穿孔時，只能選在止水帶的邊緣安裝區，不得損傷其它部分。
4 fixed strip b: the use of additional reinforcement fixation; special fixture fixed; the wire and the fixed template, such as perforation, can only choose the installation area on the strip edge, not to damage other parts.
5 用戶定貨時應根據工程結構，設計圖紙計算好產品長度，異型結構要有圖紙說明，盡量在工廠中將止水帶連接成整體，如需在現場連接時，可采用電加熱板硫化粘合或冷粘接(橡膠止水帶)或焊接(塑料止水帶)的方法.
背貼式橡膠止水帶320*6mm
5 user orders should be based on the engineering structure design drawings, calculate the length of products, have special structure drawings and specifications, try to connect into a whole band in the factory will stop, if necessary in the field of connection, can use electric heating plate vulcanization bonding or cold bonding (rubber waterstop) or welding (plastic waterstop) b.
橡膠止水帶是用來進行止水的;鋼邊橡膠止水帶在橡膠中間焊止水片外面近模板處焊定位片,對于鋼邊橡膠止水帶要求滿焊,定位片只要牢固就可以了,定位片距模板要有一到二公分的距離,這之間加塑料或者木質墊片。拆模后剔出,割掉螺桿后用微膨脹砂漿填平。還有種國內少見 就是用短一點的螺桿外加連接螺桿,拆模后可以很方便的拆下。
The rubber sealing strip is used for sealing; steel edged rubber water stop outside the middle rubber waterstop welding near the template at the welding bing piece, the steel edged rubber water stop full welding requirements, as long as the firm bing piece can, bing distance template to one to two cm distance, plastic or wooden pads plus this. After stripping out, cut off after the mortar filled with micro expansion screw. There are kinds of domestic rare connection screw rod is a little shorter, after stripping can be easily disassembled.
河北瑞博橡塑制品有限公司是一家集橡膠支座，橡膠止水帶，伸縮縫等工程橡膠制品為主的專業生產企業。歡迎各界朋友蒞臨參觀指導，業務洽談。歡迎致電：13166570832
